Ticket #6084: dmesg.log

File dmesg.log, 15.1 KB (added by ylxu72@…, 7 years ago)

Same issue under WRTSL54GS, trunk r18221

Line 
1mal zone: 0 pages reserved
2  Normal zone: 8128 pages, LIFO batch:0
3Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
4Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
5Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
6Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
7NR_IRQS:128
8PID hash table entries: 128 (order: 7, 512 bytes)
9console [ttyS0] enabled
10Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
11Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
12Memory: 29576k/32768k available (2236k kernel code, 3192k reserved, 404k data, 132k init, 0k highmem)
13Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
14Mount-cache hash table entries: 512
15net_namespace: 1008 bytes
16NET: Registered protocol family 16
17bio: create slab <bio-0> at 0
18Switched to high resolution mode on CPU 0
19ssb: PCIcore in host mode found
20PCI: Fixing up bridge 0000:00:00.0
21PCI: Setting latency timer of device 0000:00:00.0 to 64
22PCI: Fixing up device 0000:00:00.0
23PCI: Fixing latency timer of device 0000:00:00.0 to 168
24pci 0000:00:00.0: reg 10 32bit mmio: [0x000000-0x001fff]
25pci 0000:00:00.0: reg 14 32bit mmio: [0x000000-0x7ffffff]
26pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x001fff]
27pci 0000:00:02.0: reg 10 32bit mmio: [0x000000-0x000fff]
28pci 0000:00:02.0: supports D1 D2
29pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot
30pci 0000:00:02.0: PME# disabled
31pci 0000:00:02.1: reg 10 32bit mmio: [0x000000-0x000fff]
32pci 0000:00:02.1: supports D1 D2
33pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot
34pci 0000:00:02.1: PME# disabled
35pci 0000:00:02.2: reg 10 32bit mmio: [0x000000-0x0000ff]
36pci 0000:00:02.2: supports D1 D2
37pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
38pci 0000:00:02.2: PME# disabled
39PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
40PCI: Fixing up device 0000:00:01.0
41PCI: Setting latency timer of device 0000:00:01.0 to 64
42ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
43ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
44ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
45ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
46ssb: SPROM revision 2 detected.
47ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
48NET: Registered protocol family 2
49IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
50TCP established hash table entries: 1024 (order: 1, 8192 bytes)
51TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
52TCP: Hash tables configured (established 1024 bind 1024)
53TCP reno registered
54NET: Registered protocol family 1
55squashfs: version 4.0 (2009/01/31) Phillip Lougher
56Registering mini_fo version $Id$
57JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
58msgmni has been set to 57
59alg: No test for lzma (lzma-generic)
60alg: No test for stdrng (krng)
61io scheduler noop registered
62io scheduler deadline registered (default)
63Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
64serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
65serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
66serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
67serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
68b44.c:v2.0
69eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:18:f8:c9:4a:5f
70b44: eth1: PHY Reset would not complete.
71eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:90:4c:60:00:2b
72flash init: 0x1c000000 0x02000000
73Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
74Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
75Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
76Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
77 Intel/Sharp Extended Query Table at 0x0031
78Using buffer write method
79cfi_cmdset_0001: Erase suspend on write enabled
80erase region 0: offset=0x0,size=0x20000,blocks=64
81Flash device: 0x800000 at 0x1fc00000
82bootloader size: 262144
83Creating 4 MTD partitions on "Physically mapped flash":
840x000000000000-0x000000040000 : "cfe"
850x000000040000-0x0000007e0000 : "linux"
860x00000011a000-0x0000007e0000 : "rootfs"
87mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
88mtd: partition "rootfs" set to be root filesystem
89mtd: partition "rootfs_data" created automatically, ofs=320000, len=4C0000
900x000000320000-0x0000007e0000 : "rootfs_data"
910x0000007e0000-0x000000800000 : "nvram"
92BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
93TCP westwood registered
94NET: Registered protocol family 17
95802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
96All bugs added by David S. Miller <davem@redhat.com>
97VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
98Freeing unused kernel memory: 132k freed
99Please be patient, while OpenWrt loads ...
100diag: Detected 'Linksys WRTSL54GS'
101roboswitch: Probing device eth0: <3>roboswitch: [/home/ylxu/lab/kamikaze/trunk/build_dir/linux-brcm47xx/kmod-switch/switch-robo.c:131] SIOCGETCPHYRD failed!
102roboswitch: [/home/ylxu/lab/kamikaze/trunk/build_dir/linux-brcm47xx/kmod-switch/switch-robo.c:131] SIOCGETCPHYRD failed!
103No Robo switch in managed mode found, phy_id = 0xffffffff
104roboswitch: Probing device eth1: <3>roboswitch: [/home/ylxu/lab/kamikaze/trunk/build_dir/linux-brcm47xx/kmod-switch/switch-robo.c:131] SIOCGETCPHYRD failed!
105roboswitch: [/home/ylxu/lab/kamikaze/trunk/build_dir/linux-brcm47xx/kmod-switch/switch-robo.c:131] SIOCGETCPHYRD failed!
106No Robo switch in managed mode found, phy_id = 0xffffffff
107roboswitch: Probing device eth2: No such device
108roboswitch: Probing device eth3: No such device
109b44: eth0: Link is up at 100 Mbps, full duplex.
110b44: eth0: Flow control is off for TX and off for RX.
111b44: eth0: powering down PHY
112mini_fo: using base directory: /
113mini_fo: using storage directory: /jffs
114b44: eth0: Link is up at 100 Mbps, full duplex.
115b44: eth0: Flow control is off for TX and off for RX.
116device eth0 entered promiscuous mode
117br-lan: port 1(eth0) entering forwarding state
118b44: eth1: Link is up at 100 Mbps, full duplex.
119b44: eth1: Flow control is off for TX and off for RX.
120b44: eth1: powering down PHY
121b44: eth1: Link is up at 100 Mbps, full duplex.
122b44: eth1: Flow control is off for TX and off for RX.
123PPP generic driver version 2.4.2
124NET: Registered protocol family 24
125br-lan: port 1(eth0) entering disabled state
126br-lan: port 1(eth0) entering forwarding state
127cfg80211: Using static regulatory domain info
128cfg80211: Regulatory domain: US
129        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
130        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
131        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
132        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
133        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
134        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
135        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
136cfg80211: Calling CRDA for country: US
137cfg80211: Regulatory domain changed to country: US
138        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
139        (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
140        (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
141        (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
142        (5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
143        (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
144SCSI subsystem initialized
145roboswitch: Probing device eth0: found a 5325! It's a 5350.
146usbcore: registered new interface driver usbfs
147usbcore: registered new interface driver hub
148usbcore: registered new device driver usb
149b43-phy0: Broadcom 4318 WLAN found (core revision 9)
150phy0: Selected rate control algorithm 'minstrel'
151Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
152ip_tables: (C) 2000-2006 Netfilter Core Team
153Driver 'sd' needs updating - please use bus_type methods
154ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
155PCI: Enabling device 0000:00:02.2 (0000 -> 0002)
156PCI: Fixing up device 0000:00:02.2
157ehci_hcd 0000:00:02.2: EHCI Host Controller
158ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
159ehci_hcd 0000:00:02.2: Enabling legacy PCI PM
160ehci_hcd 0000:00:02.2: irq 6, io mem 0x40002000
161ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
162usb usb1: configuration #1 chosen from 1 choice
163hub 1-0:1.0: USB hub found
164hub 1-0:1.0: 5 ports detected
165hub 1-0:1.0: over-current change on port 1
166nf_conntrack version 0.5.0 (512 buckets, 2048 max)
167CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
168nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
169sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
170usb 1-1: new high speed USB device using ehci_hcd and address 2
171ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
172PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
173PCI: Fixing up device 0000:00:02.0
174PCI: Setting latency timer of device 0000:00:02.0 to 64
175ohci_hcd 0000:00:02.0: OHCI Host Controller
176ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
177ohci_hcd 0000:00:02.0: irq 6, io mem 0x40003000
178usb usb2: configuration #1 chosen from 1 choice
179hub 2-0:1.0: USB hub found
180hub 2-0:1.0: 3 ports detected
181PCI: Enabling device 0000:00:02.1 (0000 -> 0002)
182PCI: Fixing up device 0000:00:02.1
183PCI: Setting latency timer of device 0000:00:02.1 to 64
184ohci_hcd 0000:00:02.1: OHCI Host Controller
185ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
186ohci_hcd 0000:00:02.1: irq 6, io mem 0x40004000
187usb usb3: configuration #1 chosen from 1 choice
188hub 3-0:1.0: USB hub found
189hub 3-0:1.0: 2 ports detected
190ohci_hcd ssb0:2: SSB OHCI Controller
191ohci_hcd ssb0:2: new USB bus registered, assigned bus number 4
192ohci_hcd ssb0:2: irq 2, io mem 0x18003000
193usb usb4: configuration #1 chosen from 1 choice
194hub 4-0:1.0: USB hub found
195hub 4-0:1.0: 2 ports detected
196Initializing USB Mass Storage driver...
197usbcore: registered new interface driver usb-storage
198USB Mass Storage support registered.
199usb 1-1: configuration #1 chosen from 1 choice
200scsi0 : SCSI emulation for USB Mass Storage devices
201hub 2-0:1.0: over-current change on port 1
202usb-storage: device found at 2
203usb-storage: waiting for device to settle before scanning
204b43 ssb1:0: firmware: requesting b43/ucode5.fw
205b43 ssb1:0: firmware: requesting b43/pcm5.fw
206b43 ssb1:0: firmware: requesting b43/b0g0initvals5.fw
207b43 ssb1:0: firmware: requesting b43/b0g0bsinitvals5.fw
208b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
209Registered led device: b43-phy0::tx
210Registered led device: b43-phy0::rx
211Registered led device: b43-phy0::radio
212device wlan0 entered promiscuous mode
213br-lan: port 2(wlan0) entering disabled state
214b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
215Registered led device: b43-phy0::tx
216Registered led device: b43-phy0::rx
217Registered led device: b43-phy0::radio
218br-lan: port 2(wlan0) entering forwarding state
219scsi 0:0:0:0: Direct-Access     Generic  USB Disk         9.02 PQ: 0 ANSI: 2
220usb-storage: device scan complete
221sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
222sd 0:0:0:0: [sda] Write Protect is off
223sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
224sd 0:0:0:0: [sda] Assuming drive cache: write through
225sd 0:0:0:0: [sda] Assuming drive cache: write through
226 sda: sda1
227sd 0:0:0:0: [sda] Attached SCSI disk
228kjournald starting.  Commit interval 5 seconds
229EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
230EXT3 FS on sda1, internal journal
231EXT3-fs: mounted filesystem with writeback data mode.
232br-lan: port 2(wlan0) entering disabled state
233br-lan: port 1(eth0) entering disabled state
234b44: eth0: powering down PHY
235device wlan0 left promiscuous mode
236br-lan: port 2(wlan0) entering disabled state
237device eth0 left promiscuous mode
238br-lan: port 1(eth0) entering disabled state
239b44: eth1: powering down PHY
240b44: eth0: Link is up at 100 Mbps, full duplex.
241b44: eth0: Flow control is off for TX and off for RX.
242b44: eth0: powering down PHY
243b44: eth0: Link is up at 100 Mbps, full duplex.
244b44: eth0: Flow control is off for TX and off for RX.
245device eth0 entered promiscuous mode
246br-lan: port 1(eth0) entering forwarding state
247device wlan0 entered promiscuous mode
248br-lan: port 2(wlan0) entering forwarding state
249b44: eth1: Link is up at 100 Mbps, full duplex.
250b44: eth1: Flow control is off for TX and off for RX.
251b44: eth1: powering down PHY
252b44: eth1: Link is up at 100 Mbps, full duplex.
253b44: eth1: Flow control is off for TX and off for RX.
254b44: eth1: powering down PHY
255b44: eth1: Link is up at 100 Mbps, full duplex.
256b44: eth1: Flow control is off for TX and off for RX.
257br-lan: port 2(wlan0) entering disabled state
258br-lan: port 1(eth0) entering disabled state
259br-lan: port 2(wlan0) entering forwarding state
260br-lan: port 1(eth0) entering forwarding state
261br-lan: port 2(wlan0) entering disabled state
262device wlan0 left promiscuous mode
263br-lan: port 2(wlan0) entering disabled state
264b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
265Registered led device: b43-phy0::tx
266Registered led device: b43-phy0::rx
267Registered led device: b43-phy0::radio
268device wlan0 entered promiscuous mode
269br-lan: port 2(wlan0) entering disabled state
270b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
271Registered led device: b43-phy0::tx
272Registered led device: b43-phy0::rx
273Registered led device: b43-phy0::radio
274br-lan: port 2(wlan0) entering forwarding state
275tun: Universal TUN/TAP device driver, 1.6
276tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
277br-lan: port 2(wlan0) entering disabled state
278br-lan: port 1(eth0) entering disabled state
279b44: eth0: powering down PHY
280device wlan0 left promiscuous mode
281br-lan: port 2(wlan0) entering disabled state
282device eth0 left promiscuous mode
283br-lan: port 1(eth0) entering disabled state
284b44: eth1: powering down PHY
285b44: eth0: Link is up at 100 Mbps, full duplex.
286b44: eth0: Flow control is off for TX and off for RX.
287b44: eth0: powering down PHY
288b44: eth0: Link is up at 100 Mbps, full duplex.
289b44: eth0: Flow control is off for TX and off for RX.
290device eth0 entered promiscuous mode
291br-lan: port 1(eth0) entering forwarding state
292device wlan0 entered promiscuous mode
293br-lan: port 2(wlan0) entering forwarding state
294b44: eth1: Link is up at 100 Mbps, full duplex.
295b44: eth1: Flow control is off for TX and off for RX.
296b44: eth1: powering down PHY
297b44: eth1: Link is up at 100 Mbps, full duplex.
298b44: eth1: Flow control is off for TX and off for RX.
299b44: eth1: powering down PHY
300b44: eth1: Link is up at 100 Mbps, full duplex.
301b44: eth1: Flow control is off for TX and off for RX.
302br-lan: port 2(wlan0) entering disabled state
303br-lan: port 1(eth0) entering disabled state
304br-lan: port 2(wlan0) entering forwarding state
305br-lan: port 1(eth0) entering forwarding state
306br-lan: port 2(wlan0) entering disabled state
307device wlan0 left promiscuous mode
308br-lan: port 2(wlan0) entering disabled state
309b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
310Registered led device: b43-phy0::tx
311Registered led device: b43-phy0::rx
312Registered led device: b43-phy0::radio
313device wlan0 entered promiscuous mode
314br-lan: port 2(wlan0) entering disabled state
315b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
316Registered led device: b43-phy0::tx
317Registered led device: b43-phy0::rx
318Registered led device: b43-phy0::radio
319br-lan: port 2(wlan0) entering forwarding state