Ticket #7403: wifi_hang-dmesg_output.txt

File wifi_hang-dmesg_output.txt, 13.2 KB (added by ldolse, 6 years ago)

dmesg output

Line 
1root@OpenWrt:~# dmesg
2Linux version 2.6.32.10 (lee@lee-dev) (gcc version 4.3.3 (GCC) ) #2 Sun May 30 10:45:54 MYT 2010
3CPU revision is: 00029029 (Broadcom BCM3302)
4ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
5ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
6ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
7ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
8ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
9ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
10ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
11ssb: Found rev 0 PMU (capabilities 0x04A63400)
12ssb: Initializing MIPS core...
13ssb: set_irq: core 0x0806, irq 4 => 4
14ssb: set_irq: core 0x0816, irq 5 => 2
15ssb: set_irq: core 0x0812, irq 2 => 5
16ssb: after irq reconfiguration
17ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
18ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
19ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
20ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
21ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
22ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
23ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
24ssb: Sonics Silicon Backplane found at address 0x18000000
25Serial init done.
26Determined physical RAM map:
27 memory: 02000000 @ 00000000 (usable)
28Initrd not found or empty - disabling initrd
29Zone PFN ranges:
30  Normal   0x00000000 -> 0x00002000
31Movable zone start PFN for each node
32early_node_map[1] active PFN ranges
33    0: 0x00000000 -> 0x00002000
34On node 0 totalpages: 8192
35free_area_init_node: node 0, pgdat 802a3b10, node_mem_map 81000000
36  Normal zone: 64 pages used for memmap
37  Normal zone: 0 pages reserved
38  Normal zone: 8128 pages, LIFO batch:0
39Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
40Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
41PID hash table entries: 128 (order: -3, 512 bytes)
42Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
43Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
44Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
45Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
46Memory: 29504k/32768k available (2229k kernel code, 3264k reserved, 471k data, 136k init, 0k highmem)
47Hierarchical RCU implementation.
48NR_IRQS:128
49console [ttyS0] enabled
50Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
51Mount-cache hash table entries: 512
52NET: Registered protocol family 16
53bio: create slab <bio-0> at 0
54Switching to clocksource MIPS
55NET: Registered protocol family 2
56IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
57TCP established hash table entries: 1024 (order: 1, 8192 bytes)
58TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
59TCP: Hash tables configured (established 1024 bind 1024)
60TCP reno registered
61NET: Registered protocol family 1
62squashfs: version 4.0 (2009/01/31) Phillip Lougher
63Registering mini_fo version $Id$
64JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
65msgmni has been set to 57
66io scheduler noop registered
67io scheduler deadline registered (default)
68Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
69serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
70serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
71serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
72serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
73flash init: 0x1c000000 0x02000000
74Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
75Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
76Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
77Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
78 Amd/Fujitsu Extended Query Table at 0x0040
79number of CFI chips: 1
80cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
81Flash device: 0x800000 at 0x1fc00000
82bootloader size: 131072
83Updating TRX offsets and length:
84old trx = [0x0000001c, 0x00000974, 0x000e2800], len=0x00521000 crc32=0xfb2d1252
85new trx = [0x0000001c, 0x00000974, 0x000e2800], len=0x000e2800 crc32=0xf6de2be0
86Done
87Creating 4 MTD partitions on "Physically mapped flash":
880x000000000000-0x000000020000 : "cfe"
890x000000020000-0x0000007f0000 : "linux"
900x000000102800-0x0000007f0000 : "rootfs"
91mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
92mtd: partition "rootfs" set to be root filesystem
93mtd: partition "rootfs_data" created automatically, ofs=520000, len=2D0000
940x000000520000-0x0000007f0000 : "rootfs_data"
950x0000007f0000-0x000000800000 : "nvram"
96b44.c:v2.0
97eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 90:e6:ba:43:6d:71
98BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
99TCP westwood registered
100NET: Registered protocol family 17
101802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
102All bugs added by David S. Miller <davem@redhat.com>
103VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
104Freeing unused kernel memory: 136k freed
105Please be patient, while OpenWrt loads ...
106diag: Detected 'ASUS WL-500g Premium V2'
107b44: eth0: Link is up at 100 Mbps, full duplex.
108b44: eth0: Flow control is off for TX and off for RX.
109roboswitch: Probing device eth0: found a 5325! It's a 5350.
110jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
111jffs2_build_filesystem(): unlocking the mtd device... done.
112jffs2_build_filesystem(): erasing all blocks after the end marker... done.
113mini_fo: using base directory: /
114mini_fo: using storage directory: /overlay
115b44: eth0: powering down PHY
116b44: eth0: Link is up at 100 Mbps, full duplex.
117b44: eth0: Flow control is off for TX and off for RX.
118device eth0.0 entered promiscuous mode
119device eth0 entered promiscuous mode
120br-lan: port 1(eth0.0) entering forwarding state
121Generic kernel compatibility enabled based on linux-next next-20100113
122cfg80211: Calling CRDA to update world regulatory domain
123SCSI subsystem initialized
124usbcore: registered new interface driver usbfs
125usbcore: registered new interface driver hub
126usbcore: registered new device driver usb
127cfg80211: World regulatory domain updated:
128    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
129    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
130    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
131    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
132    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
133    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
134b43-phy0: Broadcom 5354 WLAN found (core revision 13)
135phy0: Selected rate control algorithm 'minstrel'
136Registered led device: b43-phy0::tx
137Registered led device: b43-phy0::rx
138Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
139Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
140ip_tables: (C) 2000-2006 Netfilter Core Team
141ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
142nf_conntrack version 0.5.0 (463 buckets, 1852 max)
143ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
144ohci_hcd ssb0:1: SSB OHCI Controller
145ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1
146ohci_hcd ssb0:1: irq 6, io mem 0x18003000
147usb usb1: configuration #1 chosen from 1 choice
148hub 1-0:1.0: USB hub found
149hub 1-0:1.0: 2 ports detected
150ohci_hcd ssb0:1: SSB EHCI Controller
151ohci_hcd ssb0:1: new USB bus registered, assigned bus number 2
152ohci_hcd ssb0:1: irq 6, io mem 0x18003800
153ohci_hcd ssb0:1: USB 0.0 started, EHCI 1.00
154usb usb2: configuration #1 chosen from 1 choice
155hub 2-0:1.0: USB hub found
156hub 2-0:1.0: 2 ports detected
157uhci_hcd: USB Universal Host Controller Interface driver
158usb 2-1: new high speed USB device using ohci_hcd and address 2
159usb 2-1: configuration #1 chosen from 1 choice
160hub 2-1:1.0: USB hub found
161hub 2-1:1.0: 2 ports detected
162usbcore: registered new interface driver snd-usb-audio
163Initializing USB Mass Storage driver...
164usbcore: registered new interface driver usb-storage
165USB Mass Storage support registered.
166b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
167b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
168device wlan0 entered promiscuous mode
169br-lan: port 2(wlan0) entering forwarding state
170device wlan0 left promiscuous mode
171br-lan: port 2(wlan0) entering disabled state
172device wlan0 entered promiscuous mode
173br-lan: port 2(wlan0) entering forwarding state
174usb 2-1.2: new full speed USB device using ohci_hcd and address 3
175usb 2-1.2: configuration #1 chosen from 1 choice
176usb 2-1.1: new high speed USB device using ohci_hcd and address 4
177usb 2-1.1: configuration #1 chosen from 1 choice
178scsi0 : SCSI emulation for USB Mass Storage devices
179usb-storage: device found at 4
180usb-storage: waiting for device to settle before scanning
181scsi 0:0:0:0: Direct-Access     WD       My Passport 070A 1030 PQ: 0 ANSI: 4
182scsi 0:0:0:1: CD-ROM            WD       Virtual CD 070A  1030 PQ: 0 ANSI: 4
183sd 0:0:0:0: [sda] 1463775232 512-byte logical blocks: (749 GB/697 GiB)
184scsi 0:0:0:2: Enclosure         WD       SES Device       1030 PQ: 0 ANSI: 4
185sd 0:0:0:0: [sda] Write Protect is off
186sd 0:0:0:0: [sda] Mode Sense: 23 00 10 00
187sd 0:0:0:0: [sda] Assuming drive cache: write through
188sd 0:0:0:0: [sda] Assuming drive cache: write through
189 sda: sda1
190usb-storage: device scan complete
191sd 0:0:0:0: [sda] Assuming drive cache: write through
192sd 0:0:0:0: [sda] Attached SCSI disk
193hfs: Filesystem was not cleanly unmounted, running fsck.hfsplus is recommended.  mounting read-only.
194ohci_hcd ssb0:1: fatal error
195ohci_hcd ssb0:1: force halt; handhake b8003814 00004000 00004000 -> -145
196ohci_hcd ssb0:1: HC died; cleaning up
197usb 2-1: USB disconnect, address 2
198usb 2-1.1: USB disconnect, address 4
199usb 2-1.2: USB disconnect, address 3
200usb 1-1: new full speed USB device using ohci_hcd and address 2
201usb 1-1: not running at top speed; connect to a high speed hub
202usb 1-1: configuration #1 chosen from 1 choice
203hub 1-1:1.0: USB hub found
204hub 1-1:1.0: 2 ports detected
205usb 1-1.1: new full speed USB device using ohci_hcd and address 3
206usb 1-1.1: not running at top speed; connect to a high speed hub
207usb 1-1.1: configuration #1 chosen from 1 choice
208scsi1 : SCSI emulation for USB Mass Storage devices
209usb-storage: device found at 3
210usb-storage: waiting for device to settle before scanning
211usb 1-1.2: new full speed USB device using ohci_hcd and address 4
212usb 1-1.2: configuration #1 chosen from 1 choice
213scsi 1:0:0:0: Direct-Access     WD       My Passport 070A 1030 PQ: 0 ANSI: 4
214scsi 1:0:0:1: CD-ROM            WD       Virtual CD 070A  1030 PQ: 0 ANSI: 4
215sd 1:0:0:0: [sdb] 1463775232 512-byte logical blocks: (749 GB/697 GiB)
216scsi 1:0:0:2: Enclosure         WD       SES Device       1030 PQ: 0 ANSI: 4
217sd 1:0:0:0: [sdb] Write Protect is off
218sd 1:0:0:0: [sdb] Mode Sense: 23 00 10 00
219sd 1:0:0:0: [sdb] Assuming drive cache: write through
220usb-storage: device scan complete
221sd 1:0:0:0: [sdb] Assuming drive cache: write through
222 sdb: sdb1
223sd 1:0:0:0: [sdb] Assuming drive cache: write through
224sd 1:0:0:0: [sdb] Attached SCSI disk
225hfs: Filesystem was not cleanly unmounted, running fsck.hfsplus is recommended.  mounting read-only.
226skb_over_panic: text:80d1a5c4 len:2370 put:2370 head:80eb2000 data:80eb2040 tail:0x80eb2982 end:0x80eb2980 dev:<NULL>
227Kernel bug detected[#1]:
228Cpu 0
229$ 0   : 00000000 1000f800 0000007c 00000001
230$ 4   : 80297480 00002ebf ffffffff 00002ebf
231$ 8   : 00004000 00000000 8029dce0 00000001
232$12   : 0000000f 80239728 ffffffff 00000002
233$16   : 00eb2040 80eb2040 00000924 81e57980
234$20   : 80e26180 00000001 a0ec5010 80d21158
235$24   : 00000002 8015efd0                 
236$28   : 80ecc000 80ecddb0 00000003 8019bbbc
237Hi    : 00000000
238Lo    : 00000077
239epc   : 8019bbbc skb_put+0x74/0x90
240    Not tainted
241ra    : 8019bbbc skb_put+0x74/0x90
242Status: 1000f803    KERNEL EXL IE
243Cause : 00800024
244PrId  : 00029029 (Broadcom BCM3302)
245Modules linked in: usb_storage snd_usb_audio snd_usb_lib uhci_hcd ohci_hcd nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack ehci_hcd sd_mod ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ext2 snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd_page_alloc snd soundcore vfat fat hfsplus b43legacy b43 nls_utf8 nls_iso8859_1 nls_cp437 mac80211 usbcore scsi_mod nls_base cfg80211 compat_firmware_class compat input_core arc4 aes_generic deflate ecb cbc switch_robo switch_core diag
246Process irq/5-b43 (pid: 806, threadinfo=80ecc000, task=81f2f650, tls=00000000)
247Stack : 00000000 80d1a5c4 00000942 00000942 80eb2000 80eb2040 80eb2982 80eb2980
248        80273cac 80e26180 00000001 80d1a5c4 80ecde50 00ff0000 80e262a4 00010000
249        802d1880 00000000 81f8540c 80016838 80d21158 00010000 00010000 81f52c00
250        00008000 00010000 80e262a4 00010000 802d1880 00000000 80299314 80d07280
251        80ecdfe0 81f2f650 80e26280 81f2f650 81f2f7e0 80e262a4 00010000 802d1880
252        ...
253Call Trace:
254[<8019bbbc>] skb_put+0x74/0x90
255[<80d1a5c4>] b43_dma_rx+0x350/0x474 [b43]
256[<80d07280>] b43_controller_restart+0x7a8/0x97c [b43]
257
258
259Code: afab001c  0c0028c2  afa20020 <0200000d> 08066ef0  00000000  8fbf002c  01201021  03e00008
260Disabling lock debugging due to kernel taint
261exiting task "irq/5-b43" (806) is an active IRQ thread (irq 5)
262root@OpenWrt:~#