Ticket #9264: dmesg

File dmesg, 13.1 KB (added by dk_giuse <dk_giuse89@…>, 5 years ago)
1root@debwrt:~# dmesg
2Linux version (giuse@EE-pc) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #6 Mon Apr 18 22:47:46 CEST 2011
3prom: fw_arg0=00000002, fw_arg1=80050028, fw_arg2=80050000, fw_arg3=00000001
4MyLoader: sysp=00000000, boardp=00000000, parts=ace50014
5bootconsole [early0] enabled
6CPU revision is: 00019374 (MIPS 24Kc)
7SoC: Atheros AR7161 rev 2
8Clocks: CPU:720.000MHz, DDR:360.000MHz, AHB:180.000MHz, Ref:40.000MHz
9Determined physical RAM map:
10 memory: 08000000 @ 00000000 (usable)
11Initrd not found or empty - disabling initrd
12Zone PFN ranges:
13  Normal   0x00000000 -> 0x00008000
14Movable zone start PFN for each node
15early_node_map[1] active PFN ranges
16    0: 0x00000000 -> 0x00008000
17On node 0 totalpages: 32768
18free_area_init_node: node 0, pgdat 80348800, node_mem_map 81000000
19  Normal zone: 256 pages used for memmap
20  Normal zone: 0 pages reserved
21  Normal zone: 32512 pages, LIFO batch:7
22pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
23pcpu-alloc: [0] 0
24Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
25Kernel command line:  board=UBNT-RSPRO console=ttyS0,115200 ethaddr=00.15.6d.c1.c9.17 root=/dev/sda1 init=/sbin/init rootdelay=15 noinitrd console=ttyS0,115200 netconsole=6665@,6666@
26PID hash table entries: 512 (order: -1, 2048 bytes)
27Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
28Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
29Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
30Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
31Writing ErrCtl register=000007c2
32Readback ErrCtl register=000007c2
33Memory: 126252k/131072k available (2500k kernel code, 4820k reserved, 479k data, 180k init, 0k highmem)
34SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
36Calibrating delay loop... 478.41 BogoMIPS (lpj=2392064)
37pid_max: default: 32768 minimum: 301
38Mount-cache hash table entries: 512
39NET: Registered protocol family 16
40MIPS: machine is Ubiquiti RouterStation Pro
41registering PCI controller with io_map_base unset
42bio: create slab <bio-0> at 0
43SCSI subsystem initialized
44usbcore: registered new interface driver usbfs
45usbcore: registered new interface driver hub
46usbcore: registered new device driver usb
47pci 0000:00:00.0: [0700:1107] type 0 class 0x000000
48pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0fffffff pref]
49pci 0000:00:00.0: reg 14: [io  0x0000-0x00ff]
50pci 0000:00:00.0: supports D1 D2
51pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
52pci 0000:00:00.0: PME# disabled
53pci 0000:00:11.0: [105a:4d69] type 0 class 0x000180
54pci 0000:00:11.0: reg 10: [io  0x01f0-0x01f7]
55pci 0000:00:11.0: reg 14: [io  0x03f4-0x03f7]
56pci 0000:00:11.0: reg 18: [io  0x0170-0x0177]
57pci 0000:00:11.0: reg 1c: [io  0x0374-0x0377]
58pci 0000:00:11.0: reg 20: [io  0x6800-0x680f]
59pci 0000:00:11.0: reg 24: [mem 0x00000000-0x00003fff]
60pci 0000:00:11.0: reg 30: [mem 0x000dc000-0x000dffff pref]
61pci 0000:00:11.0: supports D1
62pci 0000:00:13.0: [104c:9066] type 0 class 0x000280
63pci 0000:00:13.0: reg 10: [mem 0x00000000-0x00001fff]
64pci 0000:00:13.0: reg 14: [mem 0x00000000-0x0001ffff]
65pci 0000:00:13.0: supports D1 D2
66pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot
67pci 0000:00:13.0: PME# disabled
68pci 0000:00:13.0: BAR 1: assigned [mem 0x10000000-0x1001ffff]
69pci 0000:00:13.0: BAR 1: set to [mem 0x10000000-0x1001ffff] (PCI address [0x10000000-0x1001ffff])
70pci 0000:00:11.0: BAR 5: assigned [mem 0x10020000-0x10023fff]
71pci 0000:00:11.0: BAR 5: set to [mem 0x10020000-0x10023fff] (PCI address [0x10020000-0x10023fff])
72pci 0000:00:11.0: BAR 6: assigned [mem 0x10024000-0x10027fff pref]
73pci 0000:00:13.0: BAR 0: assigned [mem 0x10028000-0x10029fff]
74pci 0000:00:13.0: BAR 0: set to [mem 0x10028000-0x10029fff] (PCI address [0x10028000-0x10029fff])
75pci 0000:00:11.0: BAR 4: can't assign io (size 0x10)
76pci 0000:00:11.0: BAR 0: can't assign io (size 0x8)
77pci 0000:00:11.0: BAR 2: can't assign io (size 0x8)
78pci 0000:00:11.0: BAR 1: can't assign io (size 0x4)
79pci 0000:00:11.0: BAR 3: can't assign io (size 0x4)
80PCI: mapping irq 72 to pin1@0000:00:11.0
81PCI: mapping irq 74 to pin1@0000:00:13.0
82Switching to clocksource MIPS
83NET: Registered protocol family 2
84IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
85TCP established hash table entries: 4096 (order: 3, 32768 bytes)
86TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
87TCP: Hash tables configured (established 4096 bind 4096)
88TCP reno registered
89UDP hash table entries: 256 (order: 0, 4096 bytes)
90UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
91NET: Registered protocol family 1
92PCI: CLS 0 bytes, default 32
93squashfs: version 4.0 (2009/01/31) Phillip Lougher
94JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
95msgmni has been set to 246
96io scheduler noop registered
97io scheduler deadline registered (default)
98Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
99serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
100console [ttyS0] enabled, bootconsole disabled
101loop: module loaded
102Uniform Multi-Platform E-IDE driver
103ide-gd driver 1.18
104Atheros AR71xx SPI Controller driver version 0.2.4
105m25p80 spi0.0: found mx25l12805d, expected m25p80
106m25p80 spi0.0: mx25l12805d (16384 Kbytes)
107spi0.0: searching for MyLoader partition table at offset 0x10000
108spi0.0: searching for MyLoader partition table at offset 0x20000
109spi0.0: searching for MyLoader partition table at offset 0x30000
110spi0.0: searching for MyLoader partition table at offset 0x40000
111spi0.0: no MyLoader partition table found
112Searching for RedBoot partition table in spi0.0 at offset 0xfe0000
113Searching for RedBoot partition table in spi0.0 at offset 0xff0000
1145 RedBoot partitions found on MTD device spi0.0
115Creating 5 MTD partitions on "spi0.0":
1160x000000000000-0x000000030000 : "RedBoot"
1170x000000030000-0x000000140000 : "kernel"
1180x000000140000-0x000000ff0000 : "rootfs"
119mtd: partition "rootfs" set to be root filesystem
120mtd: partition "rootfs_data" created automatically, ofs=150000, len=EA0000
1210x000000150000-0x000000ff0000 : "rootfs_data"
1220x000000ff0000-0x000000fff000 : "FIS directory"
1230x000000fff000-0x000001000000 : "RedBoot config"
124ag71xx_mdio: probed
125eth0: Atheros AG71xx at 0xb9000000, irq 4
126eth0: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Atheros AR8216/AR8316]
127eth1: Atheros AG71xx at 0xba000000, irq 5
128eth1: AR8316 switch driver attached.
129eth1: connected to PHY at ag71xx-mdio:00 [uid=004dd041, driver=Atheros AR8216/AR8316]
130netconsole: local port 6665
131netconsole: local IP
132netconsole: interface 'eth0'
133netconsole: remote port 6666
134netconsole: remote IP
135netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
136netconsole: device eth0 not up yet, forcing it
137ar71xx: pll_reg 0xb8050010: 0x1099
138eth0: link up (100Mbps/Full duplex)
139console [netcon0] enabled
140netconsole: network logging started
141usbmon: debugfs is not available
142ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
143ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller
144ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
145ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
146ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
147usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
148usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
149usb usb1: Product: Atheros AR71xx built-in EHCI controller
150usb usb1: Manufacturer: Linux ehci_hcd
151usb usb1: SerialNumber: ar71xx-ehci
152hub 1-0:1.0: USB hub found
153hub 1-0:1.0: 2 ports detected
154ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
155ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller
156ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus number 2
157ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
158usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
159usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
160usb usb2: Product: Atheros AR71xx built-in OHCI controller
161usb usb2: Manufacturer: Linux ohci_hcd
162usb usb2: SerialNumber: ar71xx-ohci
163hub 2-0:1.0: USB hub found
164hub 2-0:1.0: 2 ports detected
165uhci_hcd: USB Universal Host Controller Interface driver
166Initializing USB Mass Storage driver...
167usbcore: registered new interface driver usb-storage
168USB Mass Storage support registered.
169usbcore: registered new interface driver ums-alauda
170usbcore: registered new interface driver ums-datafab
171usbcore: registered new interface driver ums-freecom
172usbcore: registered new interface driver ums-jumpshot
173usbcore: registered new interface driver ums-karma
174usbcore: registered new interface driver ums-sddr09
175usbcore: registered new interface driver ums-sddr55
176usbcore: registered new interface driver ums-usbat
177Atheros AR71xx hardware watchdog driver version 0.1.0
178ar71xx-wdt: timeout=15 secs (max=23)
179TCP westwood registered
180NET: Registered protocol family 17
181Bridge firewalling registered
182802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
183All bugs added by David S. Miller <davem@redhat.com>
184Waiting 15sec before mounting root device...
185usb 1-2: new high speed USB device using ar71xx-ehci and address 3
186usb 1-2: New USB device found, idVendor=05e3, idProduct=0723
187usb 1-2: New USB device strings: Mfr=3, Product=4, SerialNumber=2
188usb 1-2: Product: USB Storage
189usb 1-2: Manufacturer: Generic
190usb 1-2: SerialNumber: 000000009451
191usb-storage 1-2:1.0: Quirks match for vid 05e3 pid 0723: 8000
192scsi0 : usb-storage 1-2:1.0
193usb 2-1: new full speed USB device using ar71xx-ohci and address 2
194usb 2-1: New USB device found, idVendor=0a12, idProduct=0001
195usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
196scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9451 PQ: 0 ANSI: 0
197sd 0:0:0:0: [sda] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
198sd 0:0:0:0: [sda] Write Protect is off
199sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
200sd 0:0:0:0: [sda] Assuming drive cache: write through
201sd 0:0:0:0: [sda] Assuming drive cache: write through
202 sda: sda1 sda2 sda3
203sd 0:0:0:0: [sda] Assuming drive cache: write through
204sd 0:0:0:0: [sda] Attached SCSI removable disk
205EXT3-fs: barriers not enabled
206kjournald starting.  Commit interval 5 seconds
207EXT3-fs (sda1): mounted filesystem with writeback data mode
208VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
209Freeing unused kernel memory: 180k freed
210Algorithmics/MIPS FPU Emulator v1.5
211cfg80211: Calling CRDA to update world regulatory domain
212Compat-wireless backport release: compat-wireless-2011-03-30-6-g6a250de
213Backport based on wireless-testing.git master-2011-04-06
214Registered led device: ubnt:green:rf
215acx: acx-mac80211, version: v0.6.0 (git: unknown)
216acx: this driver is still EXPERIMENTAL
217acx: please read the README file and/or go to http://acx100.sourceforge.net/wiki for further information
218acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
219acx: running on a BIG-ENDIAN CPU
220 PCI/VLYNQ module initialized, waiting for cards to probe...
221acx: mutex_init(&adev->mutex); // adev = 0x8788ada0
222PCI: Enabling device 0000:00:13.0 (0000 -> 0002)
223PCI: Setting latency timer of device 0000:00:13.0 to 64
224acx: found an ACX111-based wireless network card at 0000:00:13.0, irq:74, phymem1:0x10028000, phymem2:0x10000000, mem1:0xb0028000, mem1_size:8192, mem2:0xb0000000, mem2_size:131072
225acx: the initial debug setting is 0x000A
226acx: using IRQ 74: OK
227acx: need firmware for acx111 chipset with radio ID 16
228Please provide via firmware hotplug:
229either combined firmware (single file named 'tiacx111c16')
230or two files (base firmware file 'tiacx111' + radio fw 'tiacx111r16')
231acx: need to load firmware for acx111 chipset with radio ID 16, please provide via firmware hotplug:
232acx: either one file only (<c>ombined firmware image file, radio-specific) or two files (radio-less base image file *plus* separate <r>adio-specific extension file)
233acx: requesting firmware image 'tiacx111c16'
234Bluetooth: Core ver 2.15
235NET: Registered protocol family 31
236Bluetooth: HCI device and connection manager initialized
237Bluetooth: HCI socket layer initialized
238Bluetooth: Generic Bluetooth USB driver ver 0.6
239usbcore: registered new interface driver btusb
240acx: acx_write_fw (main/combined): 0
241acx: acx_validate_fw (main/combined): 0
242acx: initializing max packet templates
243acx: acxpci_issue_cmd_timeo_debug: phy0: cmd=ACX1xx_CMD_CONFIGURE, buflen=32, timeout=49ms, type=0x0000, status=Invalid Information Element: FAILED
244acx: acx_configure_debug: phy0: type=0x0003, typestr=ACX1xx_IE_QUEUE_CONFIG, len=28: FAILED
245acx: phy0: acx111_create_dma_regions FAILED
246acx: init_mac() FAILED
247acx_pci: probe of 0000:00:13.0 failed with error -5
248acx: this driver is still EXPERIMENTAL
249acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
250acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
251acx: running on a BIG-ENDIAN CPU
252acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe...
253Error: Driver 'acx_pci' is already registered, aborting...
254Adding 262140k swap on /dev/sda2.  Priority:-1 extents:1 across:262140k
255EXT3-fs (sda1): using internal journal
256sshd (999): /proc/999/oom_adj is deprecated, please use /proc/999/oom_score_adj instead.
257ip_tables: (C) 2000-2006 Netfilter Core Team