Modify

Opened 3 years ago

Last modified 3 years ago

#18372 new defect

Astoria arv7519rw22 compilation not boot

Reported by: moonrotation@… Owned by: developers
Priority: normal Milestone: Chaos Calmer 15.05
Component: kernel Version: Trunk
Keywords: Cc:

Description

Trunk compilation not boot. Barrier breaker from downloads work but no lan.

Starting kernel ...

[    0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/L
inaro GCC 4.8-2014.04 r41989) ) #1 Fri Aug 8 02:41:13 CEST 2014
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is ARV7519 - Astoria Networks ARV7519RW22-A-LT
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=000084a4
[    0.000000] Readback ErrCtl register=000084a4
[    0.000000] Memory: 125136k/131072k available (3178k kernel code, 5936k reser
ved, 1127k data, 228k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels:
 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.284000] ifx_pcie_wait_phy_link_up timeout
[    0.288000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.400000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.500000] ifx_pcie_wait_phy_link_up timeout
[    0.504000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.616000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.716000] ifx_pcie_wait_phy_link_up timeout
[    0.720000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.832000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.932000] ifx_pcie_wait_phy_link_up timeout
[    0.936000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    1.048000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    1.148000] ifx_pcie_wait_phy_link_up timeout
[    1.152000] pcie_rc_initialize link up failed!!!!!
[    1.168000] bio: create slab <bio-0> at 0
[    1.172000] usbcore: registered new interface driver usbfs
[    1.176000] usbcore: registered new interface driver hub
[    1.180000] usbcore: registered new device driver usb
[    1.184000] Switching to clocksource MIPS
[    1.192000] NET: Registered protocol family 2
[    1.196000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    1.204000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.208000] TCP: Hash tables configured (established 1024 bind 1024)
[    1.216000] TCP: reno registered
[    1.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.224000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.232000] NET: Registered protocol family 1
[    1.236000] gptu: totally 6 16-bit timers/counters
[    1.240000] gptu: misc_register on minor 63
[    1.244000] gptu: succeeded to request irq 126
[    1.248000] gptu: succeeded to request irq 127
[    1.252000] gptu: succeeded to request irq 128
[    1.260000] gptu: succeeded to request irq 129
[    1.264000] gptu: succeeded to request irq 130
[    1.268000] gptu: succeeded to request irq 131
[    1.276000] phy-xrx200 gphy-xrx200.6: requesting lantiq/vr9_phy22f_a2x.bin
[    1.280000] phy-xrx200 gphy-xrx200.6: booting GPHY0 firmware at 78C0000
[    1.288000] phy-xrx200 gphy-xrx200.6: booting GPHY1 firmware at 78C0000
[    1.396000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.404000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[    1.412000] msgmni has been set to 244
[    1.416000] io scheduler noop registered
[    1.420000] io scheduler deadline registered (default)
[    1.428000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lant
iq,asc
[    1.436000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.436000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.448000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x00227e
[    1.456000] Amd/Fujitsu Extended Query Table at 0x0040
[    1.464000]   Amd/Fujitsu Extended Query version 1.3.
[    1.468000] number of CFI chips: 1
[    1.472000] 4 ofpart partitions found on MTD device ltq_nor
[    1.476000] Creating 4 MTD partitions on "ltq_nor":
[    1.480000] 0x000000000000-0x000000060000 : "uboot"
[    1.488000] 0x000000060000-0x000000080000 : "uboot_cfg"
[    1.496000] 0x000000080000-0x000001f80000 : "firmware"
[    1.500000] 0x0000001ec085-0x000001f80000 : "rootfs"
[    1.504000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[    1.516000] mtd: device 3 (rootfs) set to be root filesystem
[    1.520000] mtdsplit: no squashfs found in "ltq_nor"
[    1.544000] 0x000001f80000-0x000002000000 : "boardconfig"
[    1.656000] libphy: lantiq,xrx200-mdio: probed
[    1.664000] net-xrx200: invalid MAC, using random
[    1.668000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13,
irq=-1)
[    1.676000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14,
irq=-1)
[    1.684000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11,
irq=-1)
[    1.692000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12,
irq=-1)
[    1.700000] net-xrx200: invalid MAC, using random
[    1.704000] eth1: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    1.712000] wdt 1f8803f0.watchdog: Init done
[    1.716000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.724000] TCP: cubic registered
[    1.728000] NET: Registered protocol family 17
[    1.732000] Bridge firewalling registered
[    1.736000] 8021q: 802.1Q VLAN Support v1.8
[    1.744000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", erro
r -19
[    1.752000] List of all partitions:
[    1.756000] 1f00             384 mtdblock0  (driver?)
[    1.760000] 1f01             128 mtdblock1  (driver?)
[    1.764000] 1f02           31744 mtdblock2  (driver?)
[    1.768000] 1f03           30287 mtdblock3  (driver?)
[    1.776000] 1f04             512 mtdblock4  (driver?)
[    1.780000] No filesystem could mount root, tried:  squashfs
[    1.784000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(31,3)
I"
ROM VER: ©Œzˆø

U-Boot 2013.10-openwrt4 (Aug 10 2014 - 22:31:53) ARV7519RW22

Board: Arcadyan ARV7519RW22
SoC:   Lantiq VRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR
DRAM:  64 MiB
Flash: 32 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
ARV7519RW22 # tftpboot test-openwrt-lantiq-xrx200-ARV7519RWV12-squashfs.image
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 1, speed 100, duplex 1
ltq_phy: addr 18, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 0, speed 10, duplex 0
ltq_phy: addr 20, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.2.101; our IP address is 192.168.2.3
Filename 'test-openwrt-lantiq-xrx200-ARV7519RWV12-squashfs.image'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         ####################
         1.8 MiB/s
done
Bytes transferred = 3145732 (300004 hex)
ARV7519RW22 # bootm
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.44
   Created:      2014-07-13  11:42:55 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1494725 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.44 (bb@builder1) (gcc version 4.8.3 (OpenWrt/L
inaro GCC 4.8-2014.04 r41580) ) #2 Sat Jul 12 18:14:36 CEST 2014
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is ARV7519 - Astoria Networks ARV7519RW22-A-LT
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=000084a4
[    0.000000] Readback ErrCtl register=000084a4
[    0.000000] Memory: 125200k/131072k available (3175k kernel code, 5872k reser
ved, 1119k data, 176k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels:
 28
[    0.064000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.068000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.180000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.280000] ifx_pcie_wait_phy_link_up timeout
[    0.284000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.396000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.496000] ifx_pcie_wait_phy_link_up timeout
[    0.500000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.612000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.712000] ifx_pcie_wait_phy_link_up timeout
[    0.716000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.828000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.928000] ifx_pcie_wait_phy_link_up timeout
[    0.932000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    1.044000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    1.144000] ifx_pcie_wait_phy_link_up timeout
[    1.148000] pcie_rc_initialize link up failed!!!!!
[    1.160000] bio: create slab <bio-0> at 0
[    1.164000] usbcore: registered new interface driver usbfs
[    1.168000] usbcore: registered new interface driver hub
[    1.172000] usbcore: registered new device driver usb
[    1.176000] Switching to clocksource MIPS
[    1.184000] NET: Registered protocol family 2
[    1.188000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    1.196000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.200000] TCP: Hash tables configured (established 1024 bind 1024)
[    1.208000] TCP: reno registered
[    1.212000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.216000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.224000] NET: Registered protocol family 1
[    1.228000] gptu: totally 6 16-bit timers/counters
[    1.232000] gptu: misc_register on minor 63
[    1.236000] gptu: succeeded to request irq 126
[    1.240000] gptu: succeeded to request irq 127
[    1.244000] gptu: succeeded to request irq 128
[    1.252000] gptu: succeeded to request irq 129
[    1.256000] gptu: succeeded to request irq 130
[    1.260000] gptu: succeeded to request irq 131
[    1.268000] phy-xrx200 gphy-xrx200.6: requesting lantiq/vr9_phy22f_a2x.bin
[    1.272000] phy-xrx200 gphy-xrx200.6: booting GPHY0 firmware at 78C0000
[    1.280000] phy-xrx200 gphy-xrx200.6: booting GPHY1 firmware at 78C0000
[    1.388000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.396000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[    1.404000] msgmni has been set to 244
[    1.408000] io scheduler noop registered
[    1.412000] io scheduler deadline registered (default)
[    1.420000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lant
iq,asc
[    1.428000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.428000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.440000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x00227e
[    1.448000] Amd/Fujitsu Extended Query Table at 0x0040
[    1.456000]   Amd/Fujitsu Extended Query version 1.3.
[    1.460000] number of CFI chips: 1
[    1.464000] 4 ofpart partitions found on MTD device ltq_nor
[    1.468000] Creating 4 MTD partitions on "ltq_nor":
[    1.472000] 0x000000000000-0x000000060000 : "uboot"
[    1.480000] 0x000000060000-0x000000080000 : "uboot_cfg"
[    1.484000] 0x000000080000-0x000001f80000 : "firmware"
[    1.492000] 0x0000001ec085-0x000001f80000 : "rootfs"
[    1.496000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[    1.508000] mtd: device 3 (rootfs) set to be root filesystem
[    1.512000] mtdsplit: no squashfs found in "ltq_nor"
[    1.536000] 0x000001f80000-0x000002000000 : "boardconfig"
[    1.648000] libphy: lantiq,xrx200-mdio: probed
[    1.656000] net-xrx200: invalid MAC, using random
[    1.660000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13,
irq=-1)
[    1.668000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14,
irq=-1)
[    1.676000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11,
irq=-1)
[    1.684000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12,
irq=-1)
[    1.692000] net-xrx200: invalid MAC, using random
[    1.696000] eth1: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    1.704000] wdt 1f8803f0.watchdog: Init done
[    1.708000] leds-gpio gpio-leds.5: pins are not configured from the driver
[    1.716000] TCP: cubic registered
[    1.716000] NET: Registered protocol family 17
[    1.724000] Bridge firewalling registered
[    1.728000] 8021q: 802.1Q VLAN Support v1.8
[    1.736000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", erro
r -19
[    1.740000] List of all partitions:
[    1.744000] 1f00             384 mtdblock0  (driver?)
[    1.748000] 1f01             128 mtdblock1  (driver?)
[    1.756000] 1f02           31744 mtdblock2  (driver?)
[    1.760000] 1f03           30287 mtdblock3  (driver?)
[    1.764000] 1f04             512 mtdblock4  (driver?)
[    1.768000] No filesystem could mount root, tried:  squashfs
[    1.776000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(31,3)
H
ROM VER: ©Cˆø

U-Boot 2013.10-openwrt4 (Aug 10 2014 - 22:31:53) ARV7519RW22

Board: Arcadyan ARV7519RW22
SoC:   Lantiq VRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR
DRAM:  64 MiB
Flash: 32 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
ARV7519RW22 # printenv
addconsole=setenv bootargs $bootargs console=$consoledev,$baudrate
addeth=setenv bootargs $bootargs ethaddr=$ethaddr
addip=setenv bootargs $bootargs ip=$ipaddr:$serverip::::$netdev:off
addmachtype=setenv bootargs $bootargs machtype=ARV7519RW22
baudrate=115200
bootcmd=bootm ${kernel_addr}
bootdelay=2
consoledev=ttyLTQ1
ethact=ltq-eth
ethaddr=88:03:55:13:45:AE
ipaddr=192.168.2.3
kernel_addr=0xB0080000
load-uboot-nor=tftpboot u-boot.bin
load-uboot-norspl=tftpboot u-boot.ltq.norspl
load-uboot-norspl-lzma=tftpboot u-boot.ltq.lzma.norspl
load-uboot-norspl-lzo=tftpboot u-boot.ltq.lzo.norspl
loadaddr=0x81000000
netdev=eth0
serverip=192.168.2.101
stderr=serial
stdin=serial
stdout=serial
write-openwrt=tftpboot openwrt-lantiq-xrx200-ARV7519RWV12-squashfs.image && prot
ect off 0xB0080000 +$filesize && erase 0xB0080000 +$filesize && cp.b $fileaddr 0
xB0080000 $filesize
write-uboot-nor=protect off 0xB0000000 +$filesize && erase 0xB0000000 +$filesize
 && cp.b $fileaddr 0xB0000000 $filesize

Environment size: 1036/8188 bytes
ARV7519RW22 #
 D
ROM VER: ©Œzˆø

U-Boot 2013.10-openwrt4 (Aug 10 2014 - 22:31:53) ARV7519RW22

Board: Arcadyan ARV7519RW22
SoC:   Lantiq VRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR
DRAM:  64 MiB
Flash: 32 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
ARV7519RW22 # ls
Unknown command 'ls' - try 'help'
ARV7519RW22 # tftp test-openwrt-lantiq-xrx200-ARV7519RWV12-squashfs.image
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 18, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 1, speed 100, duplex 1
ltq_phy: addr 20, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.2.101; our IP address is 192.168.2.3
Filename 'test-openwrt-lantiq-xrx200-ARV7519RWV12-squashfs.image'.
Load address: 0x81000000
Loading: #################################################################
         #################################################################
         #################################################################
         ####################
done
Bytes transferred = 3145732 (300004 hex)
ARV7519RW22 # bootm 0xB0080000
## Booting kernel from Legacy Image at b0080000 ...
   Image Name:   MIPS OpenWrt Linux-3.14.18
   Created:      2014-11-19   1:38:18 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1491013 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.14.18 (kool@ubuntu-10) (gcc version 4.8.3 (OpenWr
t/Linaro GCC 4.8-2014.04 r43315) ) #1 Wed Nov 19 01:38:12 WET 2014
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=000084a4
[    0.000000] Readback ErrCtl register=000084a4
[    0.000000] Memory: 125256K/131072K available (3176K kernel code, 144K rwdata
, 896K rodata, 180K init, 201K bss, 5816K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels:
 28
[    0.072000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] usbcore: registered new interface driver usbfs
[    0.100000] usbcore: registered new interface driver hub
[    0.104000] usbcore: registered new device driver usb
[    0.108000] Switched to clocksource MIPS
[    0.116000] NET: Registered protocol family 2
[    0.120000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.128000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.132000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.140000] TCP: reno registered
[    0.144000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.148000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.156000] NET: Registered protocol family 1
[    0.160000] gptu: totally 6 16-bit timers/counters
[    0.164000] gptu: misc_register on minor 63
[    0.168000] gptu: succeeded to request irq 126
[    0.172000] gptu: succeeded to request irq 127
[    0.180000] gptu: succeeded to request irq 128
[    0.184000] gptu: succeeded to request irq 129
[    0.188000] gptu: succeeded to request irq 130
[    0.192000] gptu: succeeded to request irq 131
[    0.200000] phy-xrx200 gphy-xrx200.4: requesting lantiq/vr9_phy22f_a2x.bin
[    0.208000] phy-xrx200 gphy-xrx200.4: booting GPHY0 firmware at 78C0000
[    0.212000] phy-xrx200 gphy-xrx200.4: booting GPHY1 firmware at 78C0000
[    0.324000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.328000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.336000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[    0.344000] msgmni has been set to 244
[    0.348000] io scheduler noop registered
[    0.352000] io scheduler deadline registered (default)
[    0.360000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud
 = 0) is a lantiq,asc
[    0.368000] console [ttyLTQ0] enabled
[    0.368000] console [ttyLTQ0] enabled
[    0.376000] bootconsole [early0] disabled
[    0.376000] bootconsole [early0] disabled
[    0.388000] lantiq nor flash device: 02000000 at 10000000
[    0.392000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x00227e
[    0.400000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.404000]   Amd/Fujitsu Extended Query version 1.3.
[    0.412000] number of CFI chips: 1
[    0.412000] lantiq nor flash device: 02000000 at 16000000
[    0.420000] ltq-nor 10000000.nor-boot: probing failed
[    0.532000] libphy: lantiq,xrx200-mdio: probed
[    0.540000] net-xrx200: invalid MAC, using random
[    0.608000] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    0.676000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13,
irq=-1)
[    0.744000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14,
irq=-1)
[    0.812000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11,
irq=-1)
[    0.880000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12,
irq=-1)
[    0.888000] wdt 1f8803f0.watchdog: Init done
[    0.896000] TCP: cubic registered
[    0.896000] NET: Registered protocol family 17
[    0.900000] 8021q: 802.1Q VLAN Support v1.8
[    0.908000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", erro
r -19
[    0.916000] VFS: Cannot open root device "(null)" or unknown-block(0,0): erro
r -6
[    0.924000] Please append a correct "root=" boot option; here are the availab
le partitions:
[    0.932000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(0,0)
[   33.076000] random: nonblocking pool is initialized

Attachments (0)

Change History (2)

comment:1 Changed 3 years ago by moonrotation@…

I have finally managed to boot trunk compilation of changing the kernel to 3.10 but the lan ports do not work properly.
When I connect and disconnect lan cable:

root@OpenWrt:/# [  520.860000] eth0: port 4 lost link
[  520.860000] br-lan: port 1(eth0) entered disabled state
[  526.860000] eth0: port 4 got link
[  526.860000] br-lan: port 1(eth0) entered forwarding state
[  526.864000] br-lan: port 1(eth0) entered forwarding state
[  528.868000] br-lan: port 1(eth0) entered forwarding state

root@OpenWrt:/# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1): 56 data bytes
^C
--- 192.168.2.1 ping statistics ---
25 packets transmitted, 0 packets received, 100% packet loss
root@OpenWrt:/#

Example of port 1, it show as port 4

root@OpenWrt:/# [  638.860000] eth0: port 4 lost link
[  638.860000] br-lan: port 1(eth0) entered disabled state
[  639.564000] eth0: port 5 got link
[  639.564000] br-lan: port 1(eth0) entered forwarding state
[  639.568000] br-lan: port 1(eth0) entered forwarding state
[  641.572000] br-lan: port 1(eth0) entered forwarding state
root@OpenWrt:/# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1): 56 data bytes
^C
--- 192.168.2.1 ping statistics ---
6 packets transmitted, 0 packets received, 100% packet loss

Example of port 2, it show as port 5

comment:2 Changed 3 years ago by moonrotation@…

Finally I solved the problem by changing the kernel 3.10 in makefile and removing the patch:
0208-Lantiq-xrx200-strip-fcs.patch

root@OpenWrt:/# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1): 56 data bytes
64 bytes from 192.168.2.1: seq=0 ttl=64 time=1.023 ms
64 bytes from 192.168.2.1: seq=1 ttl=64 time=0.568 ms
^C
--- 192.168.2.1 ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.568/0.795/1.023 ms
root@OpenWrt:/# done.

Add Comment

Modify Ticket

Action
as new .
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.